{"title":"KUS Water Tank Sensors","description":"\u003cp\u003eKUS S5U water level sensors (1.5\" NPT) for fresh, grey, fuel, and diesel tanks in van and overland builds. Standard 240–33 ohm output works with most RV and marine gauges. Available in 6\", 8\", 9\", 15\", 17\", and 19\" probe lengths — match the probe to your tank depth. Pairs directly with NW Conversions wheel well, undercarriage, spare tire, and galley water tanks for Sprinter, Transit, and ProMaster.\u003c\/p\u003e","products":[{"product_id":"preorder-kus-s5u-6-fuel-amp-water-level-sensor-1-5-npt-6-probe","title":"KUS S5U-6 Water Level Sensor – 1.5\" NPT (6\" Probe)","description":"\u003ch2\u003eAbout the Product\u003c\/h2\u003e\n\u003cp\u003eThe KUS S5U-6 is a 6\" probe, 1.5\" NPT liquid level sender for water, fuel, or diesel tanks. It outputs the American Standard 240-33 ohm curve, which is what most US-market water and fuel gauges read, so it pairs with any 240-33Ω gauge without a signal converter.\u003c\/p\u003e\n\u003cp\u003eInside, a magnetic float slides along a chain of reed switches. The float is the only moving part, so there is no wiper arm to wear out or corrode.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eSpecifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProbe length: 6\"\u003c\/li\u003e\n\u003cli\u003eMounting: 1.5\" NPT male thread, hex head\u003c\/li\u003e\n\u003cli\u003eOutput: American Standard, 240Ω empty to 33Ω full\u003c\/li\u003e\n\u003cli\u003eSensing: reed switch chain with magnetic float\u003c\/li\u003e\n\u003cli\u003eResolution: 21mm\u003c\/li\u003e\n\u003cli\u003eBody: SUS 316 stainless steel\u003c\/li\u003e\n\u003cli\u003eFloat: NBR\u003c\/li\u003e\n\u003cli\u003eLeads: PVC jacketed, pink (ground) and black (signal)\u003c\/li\u003e\n\u003cli\u003eProtection rating: IP65\u003c\/li\u003e\n\u003cli\u003eOperating temp: -40°F to +185°F\u003c\/li\u003e\n\u003cli\u003ePower: 12V or 24V systems, 125mW\u003c\/li\u003e\n\u003cli\u003eManufacturer part number: \u003ca href=\"https:\/\/www.fisheriessupply.com\/kus-americas-s5u-series-npt-threaded-fuel-water-tank-sensor\/s5u06\"\u003eKUS 154006\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eMaterials \u0026amp; Certifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRated for water, gasoline, diesel, and hydraulic oil\u003c\/li\u003e\n\u003cli\u003e316 stainless steel body and NBR float, both corrosion resistant\u003c\/li\u003e\n\u003cli\u003eIP65 sealed housing\u003c\/li\u003e\n\u003cli\u003eGenuine \u003ca href=\"https:\/\/kus-usa.com\/\"\u003eKUS Americas\u003c\/a\u003e part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e(1) KUS S5U-6 sending unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation \u0026amp; Wiring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThreads into any 1.5\" NPT tank port. Use a thread sealant rated for what is in the tank.\u003c\/li\u003e\n\u003cli\u003eTurn it until the leads point toward your wire run, then snug it down. Do not overtighten.\u003c\/li\u003e\n\u003cli\u003eLeave at least 1\" between the tank bottom and the float collar (0.5\" on stainless or aluminum tanks). Measure from the inside bottom of the tank to the top of the port before picking a probe length.\u003c\/li\u003e\n\u003cli\u003ePink to ground, black to the sender terminal on your gauge. Two wires, no power feed.\u003c\/li\u003e\n\u003cli\u003eYou need a gauge on the 240-33Ω curve to read it. Most van builds do not have one until you add it, so check what your panel reads before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWe recommend these tanks for this sensor:\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/toyota-tacoma-11-gallon-wheel-well-water-tank\"\u003e11-Gallon Toyota Tacoma Wheel Well Water Tank (TOY-11)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/grenadier-fresh-tank\"\u003eGrenadier Fresh Tank\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eWorks with any tank that has a 1.5\" NPT sender port and a gauge on the American Standard 240-33Ω curve, OEM or aftermarket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eShipping\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn stock, ships in 1-2 business days.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2019\/08\/Product_Data_Sheet_KUS_S5U.pdf\"\u003eKUS S5U data sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-USA_SendingUnit_Installation_v4.pdf\"\u003eKUS sending unit install guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-Troubleshooting-Guide.pdf\"\u003eKUS troubleshooting guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/support.gocodeoverland.com\/\"\u003eGoCode install guides\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GoCode","offers":[{"title":"Default Title","offer_id":51457734213796,"sku":"KUU0426","price":69.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/files\/Untitleddesign_10.png?v=1788300864"},{"product_id":"preorder-kus-s5u-8-fuel-amp-water-level-sensor-1-5-npt-8-probe","title":"KUS S5U-8 Water Level Sensor – 1.5\" NPT (8\" Probe)","description":"\u003ch2\u003eAbout the Product\u003c\/h2\u003e\n\u003cp\u003eThe KUS S5U-8 is a 8\" probe, 1.5\" NPT liquid level sender for water, fuel, or diesel tanks. It outputs the American Standard 240-33 ohm curve, which is what most US-market water and fuel gauges read, so it pairs with any 240-33Ω gauge without a signal converter.\u003c\/p\u003e\n\u003cp\u003eInside, a magnetic float slides along a chain of reed switches. The float is the only moving part, so there is no wiper arm to wear out or corrode.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eSpecifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProbe length: 8\"\u003c\/li\u003e\n\u003cli\u003eMounting: 1.5\" NPT male thread, hex head\u003c\/li\u003e\n\u003cli\u003eOutput: American Standard, 240Ω empty to 33Ω full\u003c\/li\u003e\n\u003cli\u003eSensing: reed switch chain with magnetic float\u003c\/li\u003e\n\u003cli\u003eResolution: 21mm\u003c\/li\u003e\n\u003cli\u003eBody: SUS 316 stainless steel\u003c\/li\u003e\n\u003cli\u003eFloat: NBR\u003c\/li\u003e\n\u003cli\u003eLeads: PVC jacketed, pink (ground) and black (signal)\u003c\/li\u003e\n\u003cli\u003eProtection rating: IP65\u003c\/li\u003e\n\u003cli\u003eOperating temp: -40°F to +185°F\u003c\/li\u003e\n\u003cli\u003ePower: 12V or 24V systems, 125mW\u003c\/li\u003e\n\u003cli\u003eManufacturer part number: \u003ca href=\"https:\/\/www.fisheriessupply.com\/kus-americas-s5u-series-npt-threaded-fuel-water-tank-sensor\/s5u8\"\u003eKUS 154008\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eMaterials \u0026amp; Certifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRated for water, gasoline, diesel, and hydraulic oil\u003c\/li\u003e\n\u003cli\u003e316 stainless steel body and NBR float, both corrosion resistant\u003c\/li\u003e\n\u003cli\u003eIP65 sealed housing\u003c\/li\u003e\n\u003cli\u003eGenuine \u003ca href=\"https:\/\/kus-usa.com\/\"\u003eKUS Americas\u003c\/a\u003e part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e(1) KUS S5U-8 sending unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation \u0026amp; Wiring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThreads into any 1.5\" NPT tank port. Use a thread sealant rated for what is in the tank.\u003c\/li\u003e\n\u003cli\u003eTurn it until the leads point toward your wire run, then snug it down. Do not overtighten.\u003c\/li\u003e\n\u003cli\u003eLeave at least 1\" between the tank bottom and the float collar (0.5\" on stainless or aluminum tanks). Measure from the inside bottom of the tank to the top of the port before picking a probe length.\u003c\/li\u003e\n\u003cli\u003ePink to ground, black to the sender terminal on your gauge. Two wires, no power feed.\u003c\/li\u003e\n\u003cli\u003eYou need a gauge on the 240-33Ω curve to read it. Most van builds do not have one until you add it, so check what your panel reads before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWe recommend these tanks for this sensor:\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/11-gallon-passenger-side-undercarriage-water-tank\"\u003e11-Gallon Mercedes Sprinter Undercarriage Water Tank (SP-UC-11)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/22-gallon-driver-side-undercarriage-water-tank\"\u003e22-Gallon Mercedes Sprinter Driver Side Undercarriage Water Tank (SP-UC-22)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/16-gallon-transit-undercarriage-water-tank\"\u003e16-Gallon Transit Undercarriage Water Tank (TR-UC-16)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/20-gallon-driver-side-transit-undercarriage-water-tank\"\u003e20-Gallon Driver Side Transit Undercarriage Water Tank (TR-UC-20)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eWorks with any tank that has a 1.5\" NPT sender port and a gauge on the American Standard 240-33Ω curve, OEM or aftermarket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eShipping\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn stock, ships in 1-2 business days.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2019\/08\/Product_Data_Sheet_KUS_S5U.pdf\"\u003eKUS S5U data sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-USA_SendingUnit_Installation_v4.pdf\"\u003eKUS sending unit install guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-Troubleshooting-Guide.pdf\"\u003eKUS troubleshooting guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/support.gocodeoverland.com\/\"\u003eGoCode install guides\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GoCode","offers":[{"title":"Default Title","offer_id":51457735032996,"sku":"KUU0427","price":69.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/files\/Untitleddesign_6.png?v=1788300418"},{"product_id":"preorder-kus-s5u-9-fuel-amp-water-level-sensor-1-5-npt-9-probe","title":"KUS S5U-9 Water Level Sensor – 1.5\" NPT (9\" Probe)","description":"\u003ch2\u003eAbout the Product\u003c\/h2\u003e\n\u003cp\u003eThe KUS S5U-9 is a 9\" probe, 1.5\" NPT liquid level sender for water, fuel, or diesel tanks. It outputs the American Standard 240-33 ohm curve, which is what most US-market water and fuel gauges read, so it pairs with any 240-33Ω gauge without a signal converter.\u003c\/p\u003e\n\u003cp\u003eInside, a magnetic float slides along a chain of reed switches. The float is the only moving part, so there is no wiper arm to wear out or corrode.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eSpecifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProbe length: 9\"\u003c\/li\u003e\n\u003cli\u003eMounting: 1.5\" NPT male thread, hex head\u003c\/li\u003e\n\u003cli\u003eOutput: American Standard, 240Ω empty to 33Ω full\u003c\/li\u003e\n\u003cli\u003eSensing: reed switch chain with magnetic float\u003c\/li\u003e\n\u003cli\u003eResolution: 21mm\u003c\/li\u003e\n\u003cli\u003eBody: SUS 316 stainless steel\u003c\/li\u003e\n\u003cli\u003eFloat: NBR\u003c\/li\u003e\n\u003cli\u003eLeads: PVC jacketed, pink (ground) and black (signal)\u003c\/li\u003e\n\u003cli\u003eProtection rating: IP65\u003c\/li\u003e\n\u003cli\u003eOperating temp: -40°F to +185°F\u003c\/li\u003e\n\u003cli\u003ePower: 12V or 24V systems, 125mW\u003c\/li\u003e\n\u003cli\u003eManufacturer part number: \u003ca href=\"https:\/\/www.fisheriessupply.com\/kus-americas-s5u-series-npt-threaded-fuel-water-tank-sensor\/s5u09\"\u003eKUS 154009\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eMaterials \u0026amp; Certifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRated for water, gasoline, diesel, and hydraulic oil\u003c\/li\u003e\n\u003cli\u003e316 stainless steel body and NBR float, both corrosion resistant\u003c\/li\u003e\n\u003cli\u003eIP65 sealed housing\u003c\/li\u003e\n\u003cli\u003eGenuine \u003ca href=\"https:\/\/kus-usa.com\/\"\u003eKUS Americas\u003c\/a\u003e part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e(1) KUS S5U-9 sending unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation \u0026amp; Wiring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThreads into any 1.5\" NPT tank port. Use a thread sealant rated for what is in the tank.\u003c\/li\u003e\n\u003cli\u003eTurn it until the leads point toward your wire run, then snug it down. Do not overtighten.\u003c\/li\u003e\n\u003cli\u003eLeave at least 1\" between the tank bottom and the float collar (0.5\" on stainless or aluminum tanks). Measure from the inside bottom of the tank to the top of the port before picking a probe length.\u003c\/li\u003e\n\u003cli\u003ePink to ground, black to the sender terminal on your gauge. Two wires, no power feed.\u003c\/li\u003e\n\u003cli\u003eYou need a gauge on the 240-33Ω curve to read it. Most van builds do not have one until you add it, so check what your panel reads before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWe recommend these tanks for this sensor:\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/28-gallon-sprinter-spare-tire-water-tank\"\u003e28-Gallon Spare Tire Water Tank (SP-ST-28)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/24-gallon-ford-transit-spare-tire-tank\"\u003e24-Gallon Ford Transit Spare Tire Tank (TR-ST-24)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eWorks with any tank that has a 1.5\" NPT sender port and a gauge on the American Standard 240-33Ω curve, OEM or aftermarket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eShipping\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn stock, ships in 1-2 business days.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2019\/08\/Product_Data_Sheet_KUS_S5U.pdf\"\u003eKUS S5U data sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-USA_SendingUnit_Installation_v4.pdf\"\u003eKUS sending unit install guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-Troubleshooting-Guide.pdf\"\u003eKUS troubleshooting guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/support.gocodeoverland.com\/\"\u003eGoCode install guides\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GoCode","offers":[{"title":"Default Title","offer_id":51457735458980,"sku":"KUU0378","price":69.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/files\/Untitleddesign_9.png?v=1788300768"},{"product_id":"preorder-kus-s5u-15-fuel-amp-water-level-sensor-1-5-npt-15-probe","title":"KUS S5U-15 Water Level Sensor – 1.5\" NPT (15\" Probe)","description":"\u003ch2\u003eAbout the Product\u003c\/h2\u003e\n\u003cp\u003eThe KUS S5U-15 is a 15\" probe, 1.5\" NPT liquid level sender for water, fuel, or diesel tanks. It outputs the American Standard 240-33 ohm curve, which is what most US-market water and fuel gauges read, so it pairs with any 240-33Ω gauge without a signal converter.\u003c\/p\u003e\n\u003cp\u003eInside, a magnetic float slides along a chain of reed switches. The float is the only moving part, so there is no wiper arm to wear out or corrode.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eSpecifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProbe length: 15\"\u003c\/li\u003e\n\u003cli\u003eMounting: 1.5\" NPT male thread, hex head\u003c\/li\u003e\n\u003cli\u003eOutput: American Standard, 240Ω empty to 33Ω full\u003c\/li\u003e\n\u003cli\u003eSensing: reed switch chain with magnetic float\u003c\/li\u003e\n\u003cli\u003eResolution: 21mm\u003c\/li\u003e\n\u003cli\u003eBody: SUS 316 stainless steel\u003c\/li\u003e\n\u003cli\u003eFloat: NBR\u003c\/li\u003e\n\u003cli\u003eLeads: PVC jacketed, pink (ground) and black (signal)\u003c\/li\u003e\n\u003cli\u003eProtection rating: IP65\u003c\/li\u003e\n\u003cli\u003eOperating temp: -40°F to +185°F\u003c\/li\u003e\n\u003cli\u003ePower: 12V or 24V systems, 125mW\u003c\/li\u003e\n\u003cli\u003eManufacturer part number: \u003ca href=\"https:\/\/www.fisheriessupply.com\/kus-americas-s5u-series-npt-threaded-fuel-water-tank-sensor\/s5u15\"\u003eKUS 154015\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eMaterials \u0026amp; Certifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRated for water, gasoline, diesel, and hydraulic oil\u003c\/li\u003e\n\u003cli\u003e316 stainless steel body and NBR float, both corrosion resistant\u003c\/li\u003e\n\u003cli\u003eIP65 sealed housing\u003c\/li\u003e\n\u003cli\u003eGenuine \u003ca href=\"https:\/\/kus-usa.com\/\"\u003eKUS Americas\u003c\/a\u003e part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e(1) KUS S5U-15 sending unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation \u0026amp; Wiring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThreads into any 1.5\" NPT tank port. Use a thread sealant rated for what is in the tank.\u003c\/li\u003e\n\u003cli\u003eTurn it until the leads point toward your wire run, then snug it down. Do not overtighten.\u003c\/li\u003e\n\u003cli\u003eLeave at least 1\" between the tank bottom and the float collar (0.5\" on stainless or aluminum tanks). Measure from the inside bottom of the tank to the top of the port before picking a probe length.\u003c\/li\u003e\n\u003cli\u003ePink to ground, black to the sender terminal on your gauge. Two wires, no power feed.\u003c\/li\u003e\n\u003cli\u003eYou need a gauge on the 240-33Ω curve to read it. Most van builds do not have one until you add it, so check what your panel reads before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is the sensor we recommend on our 16\" tall wheel well water tanks:\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/20-gallon-wheel-well-water-tank-left\"\u003e20-Gallon Wheel Well Water Tank - Left (SP-L-20)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/20-gallon-wheel-well-water-tank-right\"\u003e20-Gallon Wheel Well Water Tank - Right (SP-R-20)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/20-gallon-wheel-well-water-tank-centered-1\"\u003e20-Gallon Wheel Well Water Tank - Center (SP-C-20)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/25-gallon-dually-wheel-well-water-tank-copy\"\u003e22-Gallon Wheel Well Water Tank - Right (SP-R-22)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/24-gallon-wheel-well-water-tank-centered\"\u003e24-Gallon Wheel Well Water Tank - Center (SP-C-24)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/36-gallon-wheel-well-water-tank-centered\"\u003e36-Gallon Wheel Well Water Tank - Center (SP-C-36)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/24-gallon-ford-transit-wheel-well-water-tank-left\"\u003e24-Gallon Ford Transit Wheel Well Water Tank - Left (TR-L-24)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/24-gallon-ford-transit-wheel-well-water-tank-right\"\u003e24-Gallon Ford Transit Wheel Well Water Tank - Right (TR-R-24)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/24-gallon-ford-transit-wheel-well-water-tank-center\"\u003e25-Gallon Ford Transit Wheel Well Water Tank - Center (TR-C-24)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eWorks with any tank that has a 1.5\" NPT sender port and a gauge on the American Standard 240-33Ω curve, OEM or aftermarket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eShipping\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn stock, ships in 1-2 business days.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2019\/08\/Product_Data_Sheet_KUS_S5U.pdf\"\u003eKUS S5U data sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-USA_SendingUnit_Installation_v4.pdf\"\u003eKUS sending unit install guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-Troubleshooting-Guide.pdf\"\u003eKUS troubleshooting guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/support.gocodeoverland.com\/\"\u003eGoCode install guides\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GoCode","offers":[{"title":"Default Title","offer_id":51457737392292,"sku":"KUU0382","price":84.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/files\/Untitleddesign_8.png?v=1788300664"},{"product_id":"preorder-kus-s5u-17-fuel-amp-water-level-sensor-1-5-npt-17-probe","title":"KUS S5U-17 Water Level Sensor – 1.5\" NPT (17\" Probe)","description":"\u003ch2\u003eAbout the Product\u003c\/h2\u003e\n\u003cp\u003eThe KUS S5U-17 is a 17\" probe, 1.5\" NPT liquid level sender for water, fuel, or diesel tanks. It outputs the American Standard 240-33 ohm curve, which is what most US-market water and fuel gauges read, so it pairs with any 240-33Ω gauge without a signal converter.\u003c\/p\u003e\n\u003cp\u003eInside, a magnetic float slides along a chain of reed switches. The float is the only moving part, so there is no wiper arm to wear out or corrode.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eSpecifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProbe length: 17\"\u003c\/li\u003e\n\u003cli\u003eMounting: 1.5\" NPT male thread, hex head\u003c\/li\u003e\n\u003cli\u003eOutput: American Standard, 240Ω empty to 33Ω full\u003c\/li\u003e\n\u003cli\u003eSensing: reed switch chain with magnetic float\u003c\/li\u003e\n\u003cli\u003eResolution: 21mm\u003c\/li\u003e\n\u003cli\u003eBody: SUS 316 stainless steel\u003c\/li\u003e\n\u003cli\u003eFloat: NBR\u003c\/li\u003e\n\u003cli\u003eLeads: PVC jacketed, pink (ground) and black (signal)\u003c\/li\u003e\n\u003cli\u003eProtection rating: IP65\u003c\/li\u003e\n\u003cli\u003eOperating temp: -40°F to +185°F\u003c\/li\u003e\n\u003cli\u003ePower: 12V or 24V systems, 125mW\u003c\/li\u003e\n\u003cli\u003eManufacturer part number: \u003ca href=\"https:\/\/www.fisheriessupply.com\/kus-americas-s5u-series-npt-threaded-fuel-water-tank-sensor\/s5u17\"\u003eKUS 154017\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eMaterials \u0026amp; Certifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRated for water, gasoline, diesel, and hydraulic oil\u003c\/li\u003e\n\u003cli\u003e316 stainless steel body and NBR float, both corrosion resistant\u003c\/li\u003e\n\u003cli\u003eIP65 sealed housing\u003c\/li\u003e\n\u003cli\u003eGenuine \u003ca href=\"https:\/\/kus-usa.com\/\"\u003eKUS Americas\u003c\/a\u003e part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e(1) KUS S5U-17 sending unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation \u0026amp; Wiring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThreads into any 1.5\" NPT tank port. Use a thread sealant rated for what is in the tank.\u003c\/li\u003e\n\u003cli\u003eTurn it until the leads point toward your wire run, then snug it down. Do not overtighten.\u003c\/li\u003e\n\u003cli\u003eLeave at least 1\" between the tank bottom and the float collar (0.5\" on stainless or aluminum tanks). Measure from the inside bottom of the tank to the top of the port before picking a probe length.\u003c\/li\u003e\n\u003cli\u003ePink to ground, black to the sender terminal on your gauge. Two wires, no power feed.\u003c\/li\u003e\n\u003cli\u003eYou need a gauge on the 240-33Ω curve to read it. Most van builds do not have one until you add it, so check what your panel reads before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is the sensor we recommend on our galley water tanks:\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/gocodeoverland.com\/collections\/nw-conversions-rvia-certified-water-tanks-for-vans-and-rvs-copy\/products\/10-gallon-galley-tank-fresh-grey\" title=\"10 gallon galley tank\"\u003e10-Gallon Galley Water Tank (Fresh\/Grey)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/gocodeoverland.com\/collections\/nw-conversions-rvia-certified-water-tanks-for-vans-and-rvs-copy\/products\/nw-conversions-20-gallon-galley-water-tank-fresh-grey\" title=\"20 gallon galley water tank for vans\"\u003e20-Gallon Galley Water Tank (Fresh\/Grey)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eWorks with any tank that has a 1.5\" NPT sender port and a gauge on the American Standard 240-33Ω curve, OEM or aftermarket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eShipping\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn stock, ships in 1-2 business days.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2019\/08\/Product_Data_Sheet_KUS_S5U.pdf\"\u003eKUS S5U data sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-USA_SendingUnit_Installation_v4.pdf\"\u003eKUS sending unit install guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-Troubleshooting-Guide.pdf\"\u003eKUS troubleshooting guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/support.gocodeoverland.com\/\"\u003eGoCode install guides\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GoCode","offers":[{"title":"Default Title","offer_id":51457737719972,"sku":"KUU0383","price":84.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/files\/Untitleddesign_7.png?v=1788300570"},{"product_id":"preorder-kus-s5u-19-fuel-amp-water-level-sensor-1-5-npt-19-probe","title":"KUS S5U-19 Water Level Sensor – 1.5\" NPT (19\" Probe)","description":"\u003ch2\u003eAbout the Product\u003c\/h2\u003e\n\u003cp\u003eThe KUS S5U-19 is a 19\" probe, 1.5\" NPT liquid level sender for water, fuel, or diesel tanks. It outputs the American Standard 240-33 ohm curve, which is what most US-market water and fuel gauges read, so it pairs with any 240-33Ω gauge without a signal converter.\u003c\/p\u003e\n\u003cp\u003eInside, a magnetic float slides along a chain of reed switches. The float is the only moving part, so there is no wiper arm to wear out or corrode.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eSpecifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProbe length: 19\"\u003c\/li\u003e\n\u003cli\u003eMounting: 1.5\" NPT male thread, hex head\u003c\/li\u003e\n\u003cli\u003eOutput: American Standard, 240Ω empty to 33Ω full\u003c\/li\u003e\n\u003cli\u003eSensing: reed switch chain with magnetic float\u003c\/li\u003e\n\u003cli\u003eResolution: 21mm\u003c\/li\u003e\n\u003cli\u003eBody: SUS 316 stainless steel\u003c\/li\u003e\n\u003cli\u003eFloat: NBR\u003c\/li\u003e\n\u003cli\u003eLeads: PVC jacketed, pink (ground) and black (signal)\u003c\/li\u003e\n\u003cli\u003eProtection rating: IP65\u003c\/li\u003e\n\u003cli\u003eOperating temp: -40°F to +185°F\u003c\/li\u003e\n\u003cli\u003ePower: 12V or 24V systems, 125mW\u003c\/li\u003e\n\u003cli\u003eManufacturer part number: \u003ca href=\"https:\/\/www.fisheriessupply.com\/kus-americas-s5u-series-npt-threaded-fuel-water-tank-sensor\/154019f\"\u003eKUS 154019\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eMaterials \u0026amp; Certifications\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRated for water, gasoline, diesel, and hydraulic oil\u003c\/li\u003e\n\u003cli\u003e316 stainless steel body and NBR float, both corrosion resistant\u003c\/li\u003e\n\u003cli\u003eIP65 sealed housing\u003c\/li\u003e\n\u003cli\u003eGenuine \u003ca href=\"https:\/\/kus-usa.com\/\"\u003eKUS Americas\u003c\/a\u003e part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e(1) KUS S5U-19 sending unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation \u0026amp; Wiring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThreads into any 1.5\" NPT tank port. Use a thread sealant rated for what is in the tank.\u003c\/li\u003e\n\u003cli\u003eTurn it until the leads point toward your wire run, then snug it down. Do not overtighten.\u003c\/li\u003e\n\u003cli\u003eLeave at least 1\" between the tank bottom and the float collar (0.5\" on stainless or aluminum tanks). Measure from the inside bottom of the tank to the top of the port before picking a probe length.\u003c\/li\u003e\n\u003cli\u003ePink to ground, black to the sender terminal on your gauge. Two wires, no power feed.\u003c\/li\u003e\n\u003cli\u003eYou need a gauge on the 240-33Ω curve to read it. Most van builds do not have one until you add it, so check what your panel reads before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is the sensor we recommend on our 20\" tall wheel well water tanks:\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/19-gallon-slim-dually-wheel-well-water-tank\"\u003e19-Gallon Slim Dually Wheel Well Water Tank (SP-DU-19)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/25-gallon-sprinter-dually-wheel-well-water-tank\"\u003e25-Gallon Dually Wheel Well Water Tank (SP-DU-25)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/33-gallon-wheel-well-water-tank-left-sp-l-33\"\u003e33-Gallon Wheel Well Water Tank - Left (SP-L-33)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/33-gallon-wheel-well-water-tank-right\"\u003e33-Gallon Wheel Well Water Tank - Right (SP-R-33)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/nw-conversions-28-gallon-promaster-wheel-well-tank-left-pm-l-28\"\u003e28-Gallon Promaster Wheel Well Water Tank - Left (PM-L-28)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/nw-conversions-28-gallon-promaster-wheel-well-water-tank-right-pm-r-28\"\u003e28-Gallon Promaster Wheel Well Water Tank - Right (PM-R-28)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/claude.ai\/products\/28-gallon-dodge-promaster-wheel-well-water-tank-center\"\u003e28-Gallon Dodge Promaster Wheel Well Water Tank - Center (PM-C-28)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eWorks with any tank that has a 1.5\" NPT sender port and a gauge on the American Standard 240-33Ω curve, OEM or aftermarket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eShipping\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn stock, ships in 1-2 business days.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2019\/08\/Product_Data_Sheet_KUS_S5U.pdf\"\u003eKUS S5U data sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-USA_SendingUnit_Installation_v4.pdf\"\u003eKUS sending unit install guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/kus-usa.com\/wp-content\/uploads\/2020\/02\/KUS-Troubleshooting-Guide.pdf\"\u003eKUS troubleshooting guide\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/support.gocodeoverland.com\/\"\u003eGoCode install guides\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GoCode","offers":[{"title":"Default Title","offer_id":51457738178724,"sku":"KUU0384","price":84.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/files\/Untitleddesign_5.png?v=1788300314"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/8474\/4356\/collections\/Untitleddesign_8.png?v=1790958113","url":"https:\/\/gocodeoverland.com\/collections\/kus-water-tank-sensors.oembed","provider":"GoCode","version":"1.0","type":"link"}